Toggle Nav
My Cart 0

RS-100B CONVERTER SANGI ELECTRIC

Price on request – please contact us
Out of stock
SKU
050961
Out of stock

The price for this item is not shown online yet.

Ask for a price on LINE

SANGI ELECTRIC

RS-100B, SANGI ELECTRIC, Converter, RS232 to RS485 Converter, RS-232 to RS-485 Converter, Serial Converter, Serial Communication Converter, RS485 Communication Converter, RS232 RS485 Interface Converter, RS485 2-Wire Converter, 2-Channel RS485 Converter, Half Duplex, Optical Isolation, Optically Isolated Converter, Multi-drop Network, Up to 256 Devices, 110VAC, 220VAC, Industrial Communication, Industrial Automation, PLC Communication, SCADA Communication, Signal Converter, RS232 to RS485 Converter, RS232 RS485 Converter, Serial Communication Converter, RS485 Communication Device, Industrial Communication Device, Optically Isolated Converter, Half Duplex Converter, Multi-drop Communication System, PLC Communication Device, SANGI ELECTRIC Signal Converter

*Price does not include VAT

SANGI ELECTRIC RS232 to RS485 Converter Model RS-100B

The SANGI ELECTRIC RS-100B Converter is a communication signal converter between RS232 and RS485, designed for connecting control devices, machinery, and communication systems in industrial applications. It supports 2-wire RS485 and half-duplex data transmission.

The device features optical isolation circuitry between the input and output sides, which helps to isolate the communication circuits between devices and reduce the impact of electrical potential differences or interference that may occur within the system. The effectiveness of this protection depends on installation conditions and manufacturer specifications.

RS-100B supports multi-drop communication management for connecting multiple devices on an RS485 network, with a maximum device count of 256 units as specified in the catalog. It is suitable for use in automatic control systems, measurement systems, and serial communication devices in industrial plants.

General Features

  • Brand: SANGI ELECTRIC
  • Product Model: RS-100B
  • Product Type: RS232 to RS485 Converter
  • Converts signals between the RS232 and RS485 interfaces
  • Suitable for 2-Wire RS485
  • Specifies 2-Channel RS485 according to catalog information
  • Supports half-duplex communication mode
  • Features optical isolation between input and output sides
  • Supports multi-drop network connection
  • A maximum of 256 devices on the network as per catalog data
  • Powers with 110VAC or 220VAC ±10%
  • Suitable for communication systems and automatic control systems in industrial applications

Technical Specifications (Technical Specifications)

BrandSANGI ELECTRIC
ModelRS-100B
Product TypeRS232 to RS485 Converter
Communication InterfaceRS232 / RS485
RS485 Connection2-Wire, 2-Channel (Catalog Reference)
Communication ModeHalf Duplex
Signal IsolationOptical Isolation between Input and Output
Network ConfigurationMulti-drop Maximum Connected DevicesUp to 256 Devices (Catalog Reference) Power Supply110 / 220 VAC ±10% Communication StandardRS232 / RS485 ApplicationIndustrial Serial Communication

Functionality

The RS-100B Signal Converter serves to convert the signal level and format of RS232 signals into Differential RS485 signals, allowing data transmission over an RS485 network. It also supports reverse signal conversion for receiving data from remote devices.

The 2-Wire RS485 system uses Half Duplex communication where each device shares the same pair of wires for both sending and receiving data, thus requiring management to prevent simultaneous transmissions on the bus.

Optical Isolation circuitry helps isolate electrical signals between input and output while a Multi-drop configuration allows multiple RS485 devices to be connected to the same communication system within the constraints of the device and network limitations.

Installation and Usage

  • Check that the originating communication system uses an RS232 interface and that the remote device supports RS485.
  • Verify the power supply voltage of the equipment matches either 110VAC or 220VAC before powering on.
  • Connect the RS232 cable according to the pinout diagram specified in the manufacturer's manual.
  • Connect the RS485 signal pair wires according to the terminal names and wiring diagrams of the equipment.
  • Verify the correctness of the RS485 signal terminals as naming conventions A/B may differ by manufacturer.
  • Rewire the RS485 with twisted-pair cables suitable for the installation environment.
  • Position devices on a Multi-drop network and terminate lines with termination resistors according to system requirements.
  • Configure communication parameters of originating and remote devices such as Baud Rate, Data Bits, Parity, and Stop Bits to match.
  • Test data transmission and reception before putting the system into actual use.

Examples and Usage Guidelines

  • Connect a computer with an RS232 port to an RS485 device.
  • Use in conjunction with PLCs and control devices requiring communication interface conversion.
  • Connect multiple measuring devices through the RS485 Multi-drop network
  • Used in industrial machine monitoring and control systems
  • Applied in Monitoring and SCADA systems that use compatible serial communication interfaces
  • Used in automatic control systems requiring electrical signal isolation between devices
  • Considerations

    • The RS-100B is an RS232 to RS485 converter, not a USB Converter or Ethernet Converter
    • SUPPORTS RS485 Half Duplex; do not claim it as RS485 Full Duplex without confirmation data
    • Maximum 256 devices according to the catalog, but consider the capabilities of all equipment and actual network design
    • The 2-Channel information should be verified against pinout diagrams before wiring and channel usage determination
    • Check power supply voltage and selection method (110VAC or 220VAC) from the manual or unit label before connecting power
    • Verify proper termination resistor and biasing use for RS485 network
    • Check Baud Rate and maximum cable length from specific model manuals before system design
    • Check connector type and unit size from specific model documents before installation
    • Electrical system installation should be performed by a qualified person following safety measures
    Write Your Own Review
    You're reviewing:RS-100B CONVERTER SANGI ELECTRIC
    Cookie settings
    🤖 AI Assistant
    Ask about products, specs and replacement models
    Hello 👋 Ask us anything — find products, compare specs, or troubleshoot.
    🗑 Clear history