EMAS CM100DY Push Button Momentary Green 1NO, Size: 22 mm (CM Series Push Button Momentary)
EMAS CM100DY is an electrical control push button momentary switch in the CM Series Metal family for installation on control panels or electrical control cabinets. It features a green flush type button with spring return mechanism.
This model has one set of Normally Open (1NO) contacts, which change to closed circuit status when pressed and revert back to open circuit status upon release. Suitable for signal transmission in machine systems and industrial automation.
The housing is made from cast metal with a coating that resists corrosion. It is designed for installation into 22 mm diameter holes and has an IP65 front protection level when properly assembled and installed.
Features
- EMAS push button switch
- CM100DY model, CM Series Metal family
- Pull-to-operate (Spring Return) type
- Green button color
- Flush type actuator
- Contact configuration: 1NO (Normally Open)
- Hole diameter for installation Ø22 mm
- Rated current capacity of 4A at 230VAC in AC-15 application category
- Metal housing
- Contact block made from PA6.6 material, V0 grade
- Contacts made from AgNi material
- Dust and water protection level IP65 on the front side
- Suitable for installation in control cabinets and machine control panels
Technical Specifications
| Specifications | Details |
| Brand | EMAS |
| Model | CM100DY |
| Series | CM Series Metal |
| Product Type | Push Button Momentary |
| Operation | Spring Return (Momentary) |
| Actuator Type | Flush |
| Button Color | Green |
| Contact Configuration | 1NO |
| Mounting Hole Diameter | 22 mm |
| Rated Operational Current (Ie) | 4 A at 230 VAC |
| Utilization Category | AC-15 |
| Rated Insulation Voltage (Ui) | 300 V |
| Rated Impulse Withstand Voltage (Uimp) | 2.5 kV |
| Contact Material | AgNi |
| Contact Block Material | PA6.6 V0 |
| Protection Degree | IP65 (Front Side) |
| Operating Temperature | -15 to +65 °C |
| Mechanical Life | Min. 500,000 Operations |
| Electrical Life | Min. 100,000 Operations |
| Mechanical Operating Frequency | 1,200 Operations/Hour |
| Electrical Operating Frequency | 1,200 Operations/Hour |
| Insulation Resistance | Min. 10 MΩ at 500 VDC |
| Dielectric Strength (Body-Contact) | 2500 VAC |
| Dielectric Strength (Contact-Contact) | 1500 VAC |
| Cable Section | 1.5–2.5 mm² |
| Terminal Screw Torque | 1.5 Nm |
| Standards | IEC 60947-5-1, UL 508 |
| Catalog Reference | SCMA General Catalog Vol.5, D7-05 |
Operation of Momentary Push Button CM100DY
The CM100DY is a momentary push button that operates with a spring mechanism. The 1NO contact remains open in the normal state, and when the user presses the button, the contacts close to send a control command. Upon releasing the button, the contacts automatically return to their open position.
It is suitable for use as a START button or a momentary command button for PLCs, relays, or machine control systems. However, continuous operation of machinery after releasing the button requires appropriate logic control or latching circuit design.
Metal Housing CM Series (Metal Construction)
The CM Series uses a die-cast metal housing and coated surface to enhance durability, suitable for installation on machine control panels in industrial environments.
The Contact Block is made from PA6.6 rated V0 level and uses AgNi contact surfaces to support operation within the circuit control as specified by the manufacturer's ratings.
Panel Mounting Installation
The CM100DY push button model is designed for installation in Ø22 mm diameter holes, suitable for mounting on electrical control panels, machine control panels, or operator control stations with appropriately sized hole diameters.
It is advisable to check the panel thickness, rear clearance, and wiring space according to the manufacturer's technical drawing before installation.
IP65 Protection Level
The CM100DY has an IP65 protection level on the front face, which protects against dust and water jets as per standard test conditions. Proper panel mounting and assembly verification are required for this protection to be effective.
The IP65 rating does not mean that the back of the push button or wiring points can directly contact water; therefore, installation within a control cabinet or appropriate protective structure is recommended.
1NO (Normally Open Contact) Contact Surface
The 1NO contact surface opens the circuit in its normal state. When pressed, it temporarily closes the circuit, suitable for sending START signals or control commands to remote devices.
The usage rating of the contact is specified at 4A at 230VAC in Utilization Category AC-15 for control circuit loads and should not be used directly as a motor load rating.
Application Examples
- MACHINE CONTROL PANEL START button
- SIGNALING TO PLC DIGITAL INPUT
- CONTROL OF RELAY AND CONTACTOR COILS AS PER RATED SPECIFICATIONS
- AUTOMATION SYSTEM PROCESS START BUTTON
- SHORT-TERM MACHINE OPERATION CONTROL BUTTON
- OPERATOR CONTROL PANEL CONTROLS
- FACILITY AUTOMATION SYSTEM
- ELECTRICAL CONTROL CABINET AND INDUSTRIAL CONTROL SYSTEMS
Installation Precautions
- CUT POWER SOURCE BEFORE INSTALLATION OR CIRCUIT MODIFICATION
- VERIFY Ø22 mm HOLE SIZE PRIOR TO INSTALLATION
- ENSURE 1NO CONTACT MATCHES DESIGNED CIRCUIT
- SELECT WIRE GAUGE AS PER MANUFACTURER SPECIFICATIONS
- TIGHTEN TERMINAL SCREWS TO REQUIRED TORQUE
- CHECK VOLTAGE AND CURRENT RATINGS FOR SUITABILITY WITH CONTROL CIRCUIT LOADS
Install with appropriate rear protection and terminal connections.
Avoid using general push buttons to replace the Emergency Stop device designed for safety purposes.
Check the spring return function and contact operation before actual use.
Important Notes Before Purchase (Important Notes)
- The product is EMAS model CM100DY.
- This is a green Momentary Spring Return push button.
- The button face is Flush type and does not include an illuminated function in this model.
- Standard contact configuration 1NO.
- Hole mounting size Ø22 mm.
- Front IP protection level IP65.
- If a contact configuration of 1NO+1NC is required, check the CM102DY model.
- Check accessories and installation dimensions from Technical Drawing before purchasing.
